1” BSP Oval Gear Flow Meter 2 - 100lpm

Product Ref: P-23-192

In Stock

Home Delivery

United Kingdom mainland delivery from £9.95 ex VAT

Parcel Delivery (Highlands & Islands are charged at a higher fee than standard)

check delivery cost

1” BSP Oval Gear Flow Meter 2 - 100lpm What is a bunded tank?

A bunded tank consists of a 'tank within a tank'.

The inner tank is the primary storage vessel, whilst the outer tank acts as a failsafe.

In the event of a spill, surplus fuel will safely and securely be stored within the outer tank and an environmental pollution incident will be averted. 

1” BSP Oval Gear Flow Meter 2 - 100lpm Description

FMT Flow Meter:

Flow meter excellent for the management and monitoring of fuel quantities as it is dispensed. FMT flow meter provide a high quality, smooth performance coupled with accurate dispensing .

These products are desinged to meet the high demands needed for commercial and agricultural use.

Please note this flow meter is a direct replacement for most DESO dispensing tank.

Specifications:

  • 1" BSP Female Inlet/ outlet.
  • Flow Rate: 2-100lpm
  • Batch Counter: 3 digit Ressetable, Calibrated 100ml
  • Cummulative Counter: Six digit, non-resettable lpm
  • Accuracy: +/- 1%
  • Suitable for use with diesel and Lubricants

1” BSP Oval Gear Flow Meter 2 - 100lpm Specification

  • Product Code: ATK
  • Suitable For Fuel: Diesel, Lubricant

1” BSP Oval Gear Flow Meter 2 - 100lpm Installation requirements

This Oil Tank must be installed and maintained in accordance to the current OFTEC guidelines, by an OFTEC Registered Technician or similarly competent person.

Fuel Tank Shop and the manufacturer will not be responsible for oil tank installations which do not comply with these requirements.

OFTEC Base Construction Guidelines (in brief):

  • Adequate for the weight of the tank when full
  • Non-combustible, imperforate and level
  • Constructed of concrete, paving stones or stonework
  • Large enough to extend 300mm beyond ALL sides of the tanks

1” BSP Oval Gear Flow Meter 2 - 100lpm Compliancy

Compliant with:

  • BS799 part 5
  • Oil Pollution Prevention Guidelines (England & Wales) 2001 PPG2 - Above Ground Oil Storage Tanks
  • Oil Pollution Prevention Guidelines (England & Wales) 2001 PPG26 – Drum and Intermediate Bulk Container Storage

1” BSP Oval Gear Flow Meter 2 - 100lpm Delivery Information

Tanks:

The delivery of a tank can be confusing as each manufacturer offers a slightly different service and lead time. Please refer to our Delivery Information page.  Standard tank deliveries are "kerbside" which means the tank will be delivered to the kerb only and not positioned further. Should you have specific delivery requirements or restrictions, please contact us to discuss.

 

Tanks Over 2500L – Articulated Lorry – Customer Offload:

These tanks will be delivered on an articulated vehicle (approximately 16.5m long x 2.6m wide x 3m high) which has no offloading on board, it is the customer's responsibility to offload the tank, which may require a telehandler / forklift.  Curtain sided vehicles are also used, so please note that if there are obstacles or hanging branches on the road to the delivery site etc, the driver may refuse to drive the vehicle to the customer's location due to the possibility of damaging the vehicle. Please let us know if there are any obstructions before delivery, so we can arrange alternative transport.

 

18 Tonne Tail Lift HGV

This vehicle is the size of the largest bin lorries (for comparison) and is approximately 8.2m long x 2.6m wide x 4m high, often curtain sided so please note that if there are hanging branches etc, these vehicles will not attempt to drive down due to the possibility of damaging the vehicle and so it is recommended that a smaller vehicle is requested. Tanks will be lowered to the ground but not positioned as this is a kerbside delivery.  If a smaller vehicle is required, please email us at sales@fueltankshop.co.uk quoting your order number and name.

 

HIAB Delivery

HIAB delivery is available but must be requested and there will be an additional cost for this service. If a HIAB delivery is required, please email us at sales@fueltankshop.co.uk quoting your order number and name, and we will come back to you with a price for this service.

 

Accessories:

Most accessories will be delivered within 1-3 working days. If you require them quicker, we can on occasions offer a next day service (please contact us to discuss). If the item(s) are out of stock, we will advise you of the expected lead time, and you will of course have the opportunity to cancel with a full refund.

 

 

1” BSP Oval Gear Flow Meter 2 - 100lpm Returns Information

Customers may return items within 14 calendar days (as per our Terms & Conditions) - refer to section 7. **

All Items must be returned unused, refunds cannot be issued for used or previously installed items.

Please be aware that returning a tank can be complicated and expensive, so please check that you are ordering the correct item (we suggest checking the dimensions very carefully).

If you wish to return goods, please complete the form on this page to provide further information.

Once your request is approved, a valid Returns Authorisation Number (RAN) will be issued to initiate the returns process along with information on how & where to return your order along with any costs involved.

Please DO NOT return any goods without this authorisation. Goods cannot be accepted without this.

Returns are not accepted at our Minehead Office, please wait until we contact you before returning any goods.

View Fuel Tank Shop return policy now.

People who bought this also bought...